French Drain Gravel Calculator
Estimate washed gravel for a French drain or foundation drainage trench. The starter project below seeds a 60 ft × 12 in × 10 in trench of washed gravel — the typical pattern for a residential perimeter drain.
Runs 100% in your browser. Your input and files never leave your device.
What it does
Trench geometry preset
60 ft long × 12 in wide × 10 in deep is the typical residential pattern. The calculator handles the unit math so you can think in inches and feet without converting.
Washed gravel density
Defaults to washed gravel / drain rock (1665–1900 kg/m³ ≈ 2800–3200 lb/yd³) — heavier than generic crushed stone. The slider lets you match your supplier's exact number.
Lower waste defaults
Trenches contain the gravel, so spillage is minimal. The French drain preset sets compaction to 10% and waste to 5% — the lowest of any use case.
How to use French Drain Gravel Calculator
- 1Type the trench length
Measure along the centerline. Common lengths: 30–60 ft for a side perimeter, 100+ ft for a full foundation perimeter. The seeded 60 ft is a good starting point.
- 2Set width and depth
Trench widths are typically 6–12 inches; depth is 8–12 inches for a residential drain (deeper for foundation drainage). Convert to feet if needed: 12 in = 1 ft.
- 3Confirm the material is washed gravel
Don't use regular crushed stone — the fines clog the drain over time. Washed gravel (also called drain rock or #57 in some regions) is the right pick.
- 4Read tons and order
Most French drains end up needing 2–6 tons of washed gravel — usually one supplier delivery. Bagged is rarely cost-effective at this volume.
When to use this
Perimeter foundation drain
120 ft × 18 in × 24 in around a basement foundation = about 13 cubic yards or 22 tons. One tandem-dump delivery handles it.
Yard French drain
40 ft × 12 in × 10 in to redirect surface water away from a low spot = about 1.2 cubic yards or 2 tons. A single-axle dump handles small jobs.
Common errors & fixes
- My drain has a bend — how do I model it?
- Add a second region for the second straight run. Or just measure the total trench length along the centerline and use a single rectangle — the volume math doesn't care about straightness.
Technical details
| French drain preset defaults | 10% compaction, 5% waste, 10 inch depth, washed gravel. |
Frequently Asked Questions
How much gravel do I need for a French drain?
Multiply length × width × depth (in feet) for cubic feet, divide by 27 for cubic yards, then multiply by ~1.5 tons per yard for washed gravel. The calculator does this and adds modest compaction + waste — French drains are well-contained, so 10% / 5% is enough.
What kind of gravel is best for a French drain?
Washed gravel (also called drain rock or #57 in some regions). The "washed" part is the important detail — it means no fines that would clog the drain. Don't substitute regular crushed stone.
How deep should a French drain be?
8–12 inches for a yard surface drain; 18–24 inches or more for foundation drainage that needs to reach below the frost line and the bottom of the footing. Local code may dictate minimum depth.
How wide should a French drain trench be?
6–12 inches is typical for a residential drain. Wider trenches handle more water but cost more in gravel. Match the perforated pipe diameter — typically 4 inches — and leave 2 inches of gravel on each side.
Related Tools
More Everyday Utilities- Unit ConverterPrecise conversion for metric and imperial units.Free • In browser
- Weighted Grade CalculatorTrack your full syllabus across a semester. Weighted categories with assignments, drop-lowest, extra credit, what-if scenarios, target-grade reverse calculation, snapshots, and save-state — all in your browser.Free • In browser
- Percentage CalculatorCalculate percentages, find what percent one number is of another, and more.Free • In browser
Also useful: Compound Interest CalculatorStripe Fee Calculator